Fuel Drip Bunker Samplers

651324 SAMPLER BUNKER FUEL DRIP, 50MM/2" FG-K1-122-KW

IMPA:651324

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651325 SAMPLER BUNKER FUEL DRIP, 75MM/3" FG-K1-123-KW

IMPA:651325

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651326 SAMPLER BUNKER FUEL DRIP, 100MM/4" FG-K1-124-KW

IMPA:651326

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651327 SAMPLER BUNKER FUEL DRIP, 125MM/5" FG-K1-125-KW

IMPA:651327

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651328 SAMPLER BUNKER FUEL DRIP, 150MM/6" FG-K1-126-KW

IMPA:651328

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651329 SAMPLER BUNKER FUEL DRIP, 175MM/7" FG-K1-127-KW

IMPA:651329

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651330 SAMPLER BUNKER FUEL DRIP, 200MM/8" FG-K1-128-KW

IMPA:651330

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651334 SAMPLER BUNKER FUEL DRIP, 225MM/9" FG-K1-129-KW

IMPA:651334

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651335 SAMPLER BUNKER FUEL DRIP, 250MM/10" FG-K1-130-KW

IMPA:651335

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651336 SAMPLER BUNKER FUEL DRIP, 275MM/11" FG-K1-131-KW

IMPA:651336

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651337 SAMPLER BUNKER FUEL DRIP, 300MM/12" FG-K1-132-KW

IMPA:651337

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651338 SAMPLER BUNKER FUEL DRIP, 350MM/14" FG-K1-133-KW

IMPA:651338

MTML UOM:PCE

Designed for obtaining good representative fuel samples during bunkering operation. A representative oil sample will provide an accurate representation of the contaminants, additives, oxidation particulates and wear condition. *Lightweight and very easy to install - obtaining a representative bunker fuel sample quick and easy. *Complete with bunker fuel sampler joint rings. *GL & Lloyds Register approved with certificate numbers etched on the flange, GL Certified for MARPOL compliance. *IMO MARPOL 73/78 Annex VI compliant - helps you stay within the legal requirements for bunker fuel sampling. The sample is collected in a cubitainer, a consumable item of typically 5 litre capacity which is attached to the needle valve. The tube should always be installed with the holes facing the fluid direction. Adjust the needle valve to give a slow and steady drip. Time the fill rate to estimate that it will provide for sufficient sample over the expected delivery period. It is recommended that four representative samples are obtained from the delivery. The distribution of the samples being: 1. Supplier's sample; 2. Vessel's sample for on-board retention; 3. On-board analysis sample; 4. Sample for independent analysis. Material: Stainless steel 304/316 Nominal Flange Thickness: 25 / 26 mm Total Thickness (including gaskets): 31 / 32 mm

651339 CUBITAINER FOR SAMPLING FLANGE, DEVICE 5LTR CAPACITY 24'S

IMPA:651339

MTML UOM:CS

Drip samplers use disposable 'Cubitainers'. These hold the oil sample before mixing and transfer to the sample bottles. They also keep out all external contamination. Supplied in 5 litre size, and packs of 24, with numbered, tamper-evident caps, pourer carton and spout

651340 BOTTLE HDPE F/FUEL OIL SAMPLE, 750ML W/SEAL & MAIL CARTON 36S

IMPA:651340

MTML UOM:PCE

750ml HDPE (High Density Polyethylene) fuel oil sample bottle packs and mailer kits complete with numbered tamper evident caps, labels and mailing cartons used for storage and safe transportation of the samples. Sample bottles have been tested and approved for transportation of fuel oil samples by air freight or courier service. All consumables are available either as convenient individual packs, or supplied in bulk to refineries and bunker barge operations.